As a core actuating component in bulk cargo handling, scrap metal processing, and civil engineering, the hydraulic motor clamshell grab operates under demanding conditions characterized by heavy loads, high dust levels, and even impact forces; consequently, component wear and seal degradation are inevitable. Implementing standardized and systematic maintenance procedures is essential to ensure the equipment's safety, reliability, and operational efficiency.
General Maintenance Principles and Safety Preparations
Before commencing any disassembly or repair work, the following fundamental principles must be observed to ensure personnel safety and equipment integrity:
Energy Isolation and Safety Lockout: Before maintenance, the hydraulic motor clamshell grab must be physically isolated from the main power supply, and Lockout/Tagout (LOTO) procedures must be implemented to prevent accidental energization and unintended equipment operation.
System Depressurization: Before disconnecting any hydraulic lines or components, ensure that the pressure within the hydraulic system has been fully relieved to atmospheric pressure. Residual high-pressure fluid can cause severe personal injury.
Pressure Re-verification: Following any component replacement, seal repair, or reassembly, the operating pressure of each system circuit must be re-verified using a calibrated precision pressure gauge. All pressure settings must strictly adhere to the values specified in the equipment technical drawings; over-adjustment or under-adjustment is strictly prohibited.
Cleanliness Control: Hydraulic systems are highly sensitive to contaminants. All disassembly, repair, and assembly operations should be performed in a relatively clean environment. Open hydraulic lines, reservoir ports, and valve connections must be immediately sealed with dedicated dust caps or plugs to prevent the ingress of dust, fibers, or metal debris into the system.
2. Systematic Disassembly Procedure (Reverse Disassembly Method)
Disassembly must follow the principles of "outside-in," "top-to-bottom," and "accessories before main body," with specific steps applied to different assemblies.
2.1 Disassembly of Hydraulic Motor Clamshell Grab Bucket Shells (Clamshell Buckets)
Position the hydraulic motor clamshell grab bucket in the fully open state and securely support the lower frame using wooden sleepers or steel stands to ensure the connecting pins are free of load.
Remove the lower steering tie-rod bolts and the shell connecting pins in sequence. If a pin is seized due to rust or deformation, use a specialized hydraulic puller or apply heat to assist removal; avoid direct hammering that could damage the base material.
2.2 Disassembly of Steering Tie-Rods
With the hydraulic motor clamshell grab bucket held open and securely supported, remove all joint pins connecting the steering tie-rods to the upper and lower frames, then carefully remove the tie-rod assembly.
2.3 Removal of the Hydraulic Power Unit (Hydraulic Station)
Ensure the hydraulic motor clamshell grab is in the open position and disconnect the motor cable from the electrical socket.
Remove the upper protective cover and all connecting lines, collecting any residual hydraulic oil from the lines into a clean container.
Unscrew the fasteners securing the oil tank cover plate; attach lifting straps or wire ropes to the dedicated lifting handle on the motor, then steadily lift the entire hydraulic station assembly vertically.
Based on the results of the oil contamination analysis (conducted via visual inspection or an oil quality tester), decide whether to perform precision filtration or a complete oil change. Immediately seal the oil tank opening after removing the hydraulic station to prevent foreign objects from falling in.
2.4 Detachment of the Hydraulic Pump
Place the removed hydraulic station onto a dedicated turnover stand with the motor facing downward, ensuring the pump body is positioned at the top for easy disassembly.
Disconnect the rigid or flexible lines connecting the pump to the oil tank cover plate, loosen the pump mounting bolts, and lift the hydraulic pump assembly out vertically.
2.5 Removal of the Control Valve Assembly
Open the protective cover of the valve assembly, mark and record the function of the valve port corresponding to each hose, and then disconnect all the hoses.
Unscrew the mounting bolts at the base of the valve assembly and remove the control valve block as a single unit.
2.6 Removal of the Drive Motor
After the hydraulic power clamshell grab has been lifted clear of the frame, first disconnect the motor cables.
Referring to the steps in Section 2.5, remove any control valve blocks that obstruct access; then, remove the motor mounting bolts and use the lifting handle to lift the motor vertically out of the oil tank.
2.7 Removal of the Lifting Cylinder (Critical/Challenging Step)
Open the hydraulic motor clamshell grab bucket and secure the cylinder in a vertical position using specialized tooling, ensuring the piston rod is fully exposed.
Loosen the locking screws (or studs) connecting the piston rod end to the upper crossbeam and remove the retaining nut.
Detach the piston rod from the connecting block: The preferred method is to briefly activate the hydraulic system (requiring a temporary power connection) and operate the motor clamshell grab bucket in the "closing" direction; use the system's own hydraulic pressure to smoothly push the piston rod out of the tapered bore or mounting seat of the connecting block.
Heat-assisted method (alternative): If the piston rod cannot be detached normally, apply uniform, controlled heat to the connecting block (using an acetylene torch or induction heater) while simultaneously applying "closing" pressure via the hydraulic system, utilizing the principle of thermal expansion and contraction to facilitate separation. Temperature must be strictly controlled during this process to prevent material phase transformation.

Replacing the Rod Seal: If only the seal needs replacement without fully removing the hydraulic cylinder, retract the piston rod completely into the cylinder barrel, unscrew the cylinder head guide nut, and sequentially remove the old rod seal, wiper ring, and guide strip.
Removing the Entire Hydraulic Cylinder: If complete removal is required, first disconnect the hose fittings at both ends of the hydraulic motor clamshell grab's cylinder and use appropriate lifting equipment (such as a chain hoist or small crane) to support the cylinder body. Remove the locking mechanism for the pin at the lower crossbeam; by slightly adjusting the lifting equipment to relieve the load on the lower pin, you can slide the pin out laterally and remove the cylinder. For storage, the hydraulic motor clamshell grab's cylinder must be placed horizontally on V-shaped supports or wooden blocks; the piston rod surface should be coated with anti-rust oil and wrapped in a protective sleeve to prevent any impacts or scratches.
3. Component Inspection and Repair Specifications
3.1 Replacement of Structural Bushings and Pins
After disassembly, the old bushings at the shovel blade lug plates and steering tie-rod joints must be pressed out. Inspect the mating surfaces of the pins; if significant wear ridges appear or radial wear exceeds tolerance limits, the pins must also be replaced.
Before pressing in the new bushing, apply a specialized anaerobic retaining adhesive (e.g., Loctite 638) to its outer surface. Then, use a press to slowly insert the bushing until it is flush with the bore face, ensuring it is not tilted and meets bonding strength requirements.
3.2 Replacement of Hydraulic Cylinder Seal Assemblies
Rod Seal Replacement (Standard Method): Remove the cylinder end cap flange, fully extract the piston and piston rod assembly, and replace all old seals (O-rings, U-rings, Step-seals, and guide rings) with components from an OEM-specification repair kit.
Split-type Seals (Special Emergency Method): In emergency field repairs where piston removal is not feasible, split-type (open-cut) rod seals may be used as a substitute. However, note that this method is intended only for temporarily restoring functionality; the service life and sealing performance are inferior to those of solid (one-piece) seals. If this method is adopted, "split-type design" must be clearly specified when ordering spare parts.
3.3 Handling Principles for Hydraulic Pumps and Valve Assemblies
The hydraulic motor clamshell grab's hydraulic pumps (gear pumps/piston pumps): Field disassembly and repair are strongly discouraged. The precision mating components within the pump have extremely strict requirements regarding assembly clearances and cleanliness; repairs performed outside a factory environment can easily lead to secondary failure. In the event of a malfunction, the entire unit should be removed and sent back to the original manufacturer or a specialized hydraulic repair center for testing and servicing.
Control valve blocks:
When replacing the safety relief valve, remove the pilot valve spool and replace the entire pressure-regulating assembly, following the diagram on page.
When replacing a shut-off valve (ball valve or needle valve), the entire valve spool assembly must be replaced; do not replace only the seal ring. This ensures that the valve's shut-off function and internal leakage rate meet design standards.
4. Reassembly and Final Commissioning Guidelines
Reverse Assembly: Assemble the components in the exact reverse order of disassembly. During this process, exercise special care when passing components equipped with seals or O-rings over threads or sharp edges; use a dedicated installation sleeve or apply grease to guide the component and prevent the seals from being sheared or twisted.
Special Lubrication Requirements: For spherical plain bearings, the use of greases containing molybdenum disulfide additives is strictly prohibited, as this may cause fretting corrosion on the bearing surfaces. Pressure-resistant lithium-based grease conforming to standards must be used.
System Pressure Verification: Upon completion of assembly, connect the power supply and hydraulic lines, then operate the hydraulic motor clamshell grab through a no-load cycle to purge air from the system. Subsequently, connect a standard test pressure gauge to the test port, readjust the main relief valve pressure to the specified value, and verify smooth operation and the absence of external leakage.






